Bonray electric actuator BJM05-IIC BJM10-IIC BJM15-IIC BJM20-IIC BJM30-IIC BJM40-IIC BJM60-IIC BJM80-IIC BJM100-IIC BJM150-IIC BJM200-IIC BJM250-IIC BJM250-IIC BJM300-IIC

Brief Introduction:

BJ-IIC intelligent multiple-turn actuator is an important control equipment during process control.It can be quickly adjusted,inspected and inquired through an independent setting component or site knob with non invasion.Actuator using dot matrix LED to show the position,torque limitation set,working state and warning alarm by English,Russian,numbers and images.

Torque Range:

50N.m----3000N.m

Match with W series worm gearbox the torque could reach 300000N.m

Flange interface:

According to flange standard ISO5211:2001(GB/T12223-2005)

Also can match with customers special requirement flange.

Ambient Temperature:

-30℃-70℃ Optional -60℃

Optional:

Modbus Profibus-DP HART DeviceNet FF field bus card.

Separate model:

Available

Put the electric control component into a separate container from the main body of actuator,using cable between them to transfer control signal.

The housing of BJ-Q1, BD-A series intelligentelectric actuators are made of cast iron which ischaracterized by high strength and strong corTosionresistance

The transmission part uses worm and gearstructure. Meanwhile, the BJ-Q1 part rotary serieselectric actuators can provide the most reasonablesolutions in the range of output torque of 100N.m ~5000 N.m, and the BD-A multi rotary series actuatorscan provide the most reasonable solutions in therange of output torque of 100N.m ~ 500 N.m,TheBJ-Q1. BD-A series itellient electric actuatorscan add the field bus card of Modbus Profib-us-DP. HART. FF. Device-Netaccording

Main technical performance indicators

Power;

One Phaser 220Vac/50HzThree phaser 3 80Vac/50Hz(other power available)

Input signal:

DC24V. AC220V or passive contactDC4~20mA (Only for modulatingapplication ),

Output signal:

4 sets onsite output contact,

One set distance output contact and one set fault warning output contact

Water proof IP6S(IP67 available);

Explosion proof-

ExdII BT4;

-20C ~+60'C

(-30C ~+70C available).

BJ/BJM-IC partial rotary series intelligent electric actuator is a very important on-site control device in process control. It can be quickly set, checked and queried non invasively through an independent setter or on-site knob. The actuator adopts a dot matrix LCD display, which displays the working status and alarms of the actuator's torque, valve position, limit setting, etc. in Chinese, digital, graphic and other forms. The BJ/BJM-IC series electric actuators have a simple design, compact structure, and complete specifications. Their output angular displacement is 0-90 ° or other angles, and they can provide the most reasonable solution within the output torque range of 50N. m to 3000 N. m. They are widely used in fields such as power, petroleum, chemical, metallurgical, shipbuilding, light industry and food, papermaking, construction, municipal engineering, and environmental protection.

The BJ/BJM-IC series electric actuators adopt a patented planetary gear transmission mechanism. Compared with electric actuators using worm gear transmission mechanisms, BJ-IIC series intelligent electric actuators have significant technical advantages: using a two-stage gear and two-stage planetary gear transmission mechanism, the mechanical efficiency of electric actuators using worm gear transmission mechanisms is increased by more than 50%. The gears are made of high-quality structural steel, which significantly reduces mechanical wear. The manual/electric switching mechanism has been eliminated, completely solving the problem of high manual/electric switching failure rate in models using worm gear transmission mechanisms. Hand/electric switching is safe and reliable. Small size, high load-bearing capacity, and lifespan more than doubled. Any speed actuator self-locking. New exterior design, more fashionable and beautiful.

The interface flange of BJ/BJM-IC series electric actuators is manufactured according to ISO5211:2017 (GB/T12223-2023) standard, and non-standard structural flanges can also be matched according to user requirements. The actuator and valve are directly connected, which can be easily matched with rotary valves (such as butterfly valves, ball valves, plug valves) and air door baffles. The interface drive sleeve adopts a spline structure design, and the installation angle is not limited, while the reliability is greatly enhanced. The standard shell and box treated with phosphating and coating can adapt to corrosive working environments, while the explosion-proof and pressure resistant products provided in the form of options can be used in hazardous working environments such as Zone 1 and Zone 2 of IIA, IIB, IIC T1-T4 explosive gas environments; Dust explosion-proof products are suitable for hazardous working environments such as Zone 21 and 22 in environments with T130C ° explosive dust levels of Class IIIA, IIIB, and IIIC.

The BJ/BJM-IC series electric actuators can be equipped with various functional configurations by adding options according to user requirements, such as Profibus DP fieldbus cards, Modbus fieldbus cards, Devicenet fieldbus cards, FF fieldbus cards, Hart fieldbus cards, etc., to meet the requirements of various industrial process controls. To adapt to various harsh working conditions, we have evolved the BJ/BJM-IICF split type electric actuator based on the BJ/BJM-IIC series electric actuator. It installs the electrical control components into an independent controller (see Figure 5-5), which is separated from the actuator. Control signals are transmitted remotely through cables for control and feedback, and all functions of the BJ/BJM-IIC series electric actuator can be achieved. BJ/BJM-ICF split type electric actuators are widely used in harsh working conditions such as high temperature or strong vibration.

BJ10-Q BJ20-Q BJ30-Q BJ60-Q BJ90-Q BJ120-Q BJ200-Q BJ250-Q BJ300-Q BJ400-Q BJ500-Q BD10-A BD15-A BD20-A BD30-A BD45-A BD60-A BD90-A BD120-A BD180-A BD250-A BD350A-A BD350B-A BD500-A BJ05-IIC BJ10-IIC BJ15-IIC BJ20-IIC BJ30-IIC BJ40-IIC BJ60-IIC BJ80-IIC BJ100-IIC BJ101-IIC BJ150-IIC BJ200-IIC BJ330-IIC BD05-IIC BD10-IIC BD15-IIC BD20-IIC BD30-IIC BD40-IIC BD60-IIC BD100-IIC BD150-IIC BD200-IIC BD300-IIC

BJM10-Q BJM20-Q BJM30-Q BJM60-Q BJM90-Q BJM120-Q BJM200-Q BJM250-Q BJM300-Q BJM400-Q BJM500-Q BD10-A BD15-A BD20-A BD30-A BD45-A BD60-A BD90-A BD120-A BD180-A BD250-A BD350A-A BD350B-A BD500-A BJM05-IIC BJM10-IIC BJM15-IIC BJM20-IIC BJM30-IIC BJM40-IIC BJM60-IIC BJM80-IIC BJM100-IIC BJM101-IIC BJM150-IIC BJM200-IIC BJM330-IIC BD05-IIC BD10-IIC BD15-IIC BD20-IIC BD30-IIC BD40-IIC BD60-IIC BD100-IIC BD150-IIC BD200-IIC BD300-IIC

BJ10-Q1 BJ20-Q1 BJ30-Q1 BJ60-Q1 BJ90-Q1 BJ120-Q1 BJ200-Q1 BJ250-Q1 BJ300-Q1 BJ400-Q1 BJ500-Q1

BJ20-IIC BJ40-IIC BJ60-IIC BJ80-IIC BJ100-IIC BJ150-IIC BJ200-IIC BJ05-IIC BJ10-IIC BJ15-IIC BJ20-IIC BJ250-IIC BJ30-IIC BJ101-IIC BJ300-IIC
BJM05-IIC BJM10-IIC BJM15-IIC BJM20-IIC BJM30-IIC BJM40-IIC BJM60-IIC BJM80-IIC BJM100-IIC BJM150-IIC BJM200-IIC BJM250-IIC BJM250-IIC BJM300-IIC